{"id":12418,"date":"2026-09-01T12:18:03","date_gmt":"2026-09-01T12:18:03","guid":{"rendered":"https:\/\/www.raxpower.com\/?p=12418"},"modified":"2026-09-01T12:18:03","modified_gmt":"2026-09-01T12:18:03","slug":"guia-de-lavagem-de-isoladores-compostos-em-operacao","status":"publish","type":"post","link":"https:\/\/www.raxpower.com\/pt\/blog\/composite-insulator-operation-washing-guide\/","title":{"rendered":"Opera\u00e7\u00e3o de isoladores compostos em servi\u00e7o com contamina\u00e7\u00e3o"},"content":{"rendered":"

A composite insulator rarely fails because the grid asked too much of its core. Most service problems start on the surface, where salt, dust and industrial residue try to build a conductive film faster than rain can strip it off. Contamination control is therefore not housekeeping. It is the discipline that decides whether a string rides through a wet season or hands you a trip report.<\/p>\n

RaxPower has built pole line hardware since 2003 and supplies composite insulators alongside it, with 170+ people across the company. Our engineering desk reads pollution tickets from utility customers, and this guide stays inside one slice of composite insulator operation. It covers what deposits do in service, how to measure them, and when to wash. It also shows how to wash without harming the silicone housing, and where coatings take over.<\/p>\n

What Pollution Films Do During Composite Insulator Operation<\/h2>\n

Picture the housing at dawn after a coastal fog. Each shed carries a thin, damp paste of salt and dust, and the leakage path runs straight across it. That paste is the working enemy in polluted service.<\/p>\n

The film has two parts. One dissolves in water and is measured as equivalent salt deposit density, or ESDD. The other is an inert matrix measured as non-soluble deposit density, NSDD. The distinction matters because the soluble fraction carries current while the insoluble fraction holds moisture and decides how long the film stays conductive.<\/p>\n

Silicone rubber fights back with hydrophobicity. Water beads instead of filming, and low molecular weight chains migrate into the deposit so the film itself resists wetting. When deposition outruns this recovery, leakage current starts to flow, dry bands form, and localized arcing follows.<\/p>\n

\"Grey
Grey silicone rubber sheds on a polymer standoff insulator<\/figcaption><\/figure>\n

None of this is a defect story. The core, the housing and the aluminum alloy end fittings can all be healthy while the surface quietly loses the pollution race. That is why composite insulator operation treats the surface film as a managed asset with its own readings, its own calendar and its own limits.<\/p>\n

Reading the Deposit Before You Reach for Water<\/h2>\n

Escalating to washing starts with evidence, and the cheapest evidence is visual. Heavy, uniform deposits, glazed tracks, or orange arcs during humid nights all point to a surface losing margin. Utility practice treats orange partial arcs on salt films as a pre-flashover state, not a cosmetic quirk.<\/p>\n

Tripped lines add context. A sound assessment of a suspected pollution flashover compiles the basic event record first: timestamp, location, service voltage and on-site observations. Patterns across several events say more than any single incident.<\/p>\n

Treat the readings as a fleet asset. The European utility framework for composite insulator maintenance logs UV and IR findings, hydrophobicity class and ESDD\/NSDD numbers in one database, which lets a utility benchmark mitigation effects across seasons.<\/p><\/blockquote>\n

Quantification follows the same logic. Wipe sampling measures ESDD and NSDD on the top and bottom shed faces and on the trunk at several positions, and the framework records weighted averages alongside maxima. Bottom faces often collect more deposit than top faces, so a single whole-string average can hide the worst surface.<\/p>\n

In our experience, utilities that skip the measurement step wash on habit. They spend crew hours on strings that rain would have cleaned, and miss the ones quietly building toward a trip.<\/p>\n

\"Concrete
Line hardware carrying insulators through years of outdoor service<\/figcaption><\/figure>\n

Rain is part of the reading too. A site with regular wetting keeps its surfaces naturally washed, while a short rainy season lets deposits accumulate for months at a stretch. The same deposit load means different risk at these two sites.<\/p>\n

When Washing Beats Waiting on a Polluted String<\/h2>\n

Washing earns its place when deposition outruns natural cleaning, and that is the daily reality of composite insulator operation in dirty air. Coastal spray seasons, dry seasons without rain, and industrial corridors with continuous emissions all produce surfaces rain cannot keep clean. On those strings, waiting is a decision to ride the leakage current.<\/p>\n

The triggers are practical. Dense visible deposits, ESDD readings trending upward, a flashover event on the circuit, or beading that no longer recovers between patrols. Any one of them moves washing onto the schedule.<\/p>\n

There is one standing exception. A housing with cuts, exposed core or deep erosion should never be washed and returned to service. Treat it the way you would treat a cracked pump casing: hosing it down does not repair the fault. Water finds the defect faster than the dirt ever did, so damage escalates the case to replacement rather than cleaning.<\/p>\n

Between those poles sits judgment. Utilities in the European framework schedule targeted inspections and washings for high-risk weather windows, which keeps the intervention ahead of the season instead of behind the outage.<\/p>\n

How to Wash Without Harming the Silicone Housing<\/h2>\n

The housing works because of a thin surface layer, so the first rule of washing is to remove deposits without attacking the layer underneath. Water does the work. Abrasive pads, scrapers and aggressive solvents cause damage no deposit could justify.<\/p>\n

Live washing raises the stakes and brings its own rules. The water itself must insulate. Field practice sets a floor of 2,540 ohm-cm resistivity, equal to 400 microsiemens of conductivity, as the minimum for safe hot washing.<\/p>\n

IEEE 957-2024 is titled the Guide for Monitoring, Managing, and Cleaning of Contaminated Insulators. It gathers the procedures in one place: monitoring contamination, managing the risk, and cleaning insulators of all types with the equipment and techniques the job requires.<\/p><\/blockquote>\n

Two habits keep a live wash predictable. Resistivity falls as water warms, so crews monitor it continuously, and washer packages carry monitors that shut the system down when conductivity drifts past the limit. Wash guns and the truck chassis stay grounded to the structure for the same reason.<\/p>\n

    \n
  1. Confirm water resistivity at the tank, then again at the nozzle, before the first jet.<\/li>\n
  2. Keep the jet moving in a sweeping pass, never parked on one shed and never aimed into a seal.<\/li>\n
  3. Work the string section by section so dirty water always runs off already-cleaned surface.<\/li>\n
  4. On de-energized work, hand wiping with clean cloths and plain water is the gentle default.<\/li>\n
  5. Log the wash: date, water readings, sections covered and what the beading looked like afterwards.<\/li>\n<\/ol>\n

    Verification closes the job. After the string dries, a spray check shows whether water beads and rolls as it should. Beading that fails to return is not a washing failure to repeat. It is a finding for the escalation ladder later in this guide.<\/p>\n

    \n
    \n

    Specifying Composite Insulators for a Polluted Corridor?<\/h3>\n

    Compare suspension, tension and line-post units with silicone rubber housings, fiberglass cores and documented test reporting for the pollution class your line actually runs.<\/p>\n

    View the Overhead Line Insulator Range<\/a>\n<\/div>\n

    \"Overhead\n<\/div>\n

    Setting Washing Frequency From the Pollution Calendar<\/h2>\n

    Frequency is a derived number, not a preference. It follows the local pollution calendar: when deposits arrive, when rain fails to arrive, and when the wet season concentrates risk. Two lines in one utility can justify different intervals without either being wrong.<\/p>\n

    The calendar logic is simple. Sites inside a coastal spray season need coverage in front of the season, not after the first trip. Dry industrial corridors need a wash before the long rainless stretch, because natural washing will not resume for months.<\/p>\n

    \"Suspension
    Suspension insulator strings hanging on a lattice test pylon<\/figcaption><\/figure>\n

    Ceramic practice contributes a rule of thumb: severe pollution or low natural washing justifies intervention such as greasing or washing. Composite strings shift the balance, because the housing does more of the work itself. The trigger structure survives translation. What changes is the response: water first, chemistry never, and records every time.<\/p>\n

    Trend data tightens the schedule over time. A utility that logs wash dates against flashover records and deposit readings soon sees its real interval. The second season then costs less than the first.<\/p>\n

    Where RTV Coatings Fit in Composite Insulator Operation<\/h2>\n

    Coatings enter the conversation whenever washing gets expensive, and the boundary matters. RTV silicone coatings are a ceramic-string technology. IEEE 1523-2018 says so in its title: the guide for the application, maintenance and evaluation of RTV silicone rubber coatings for outdoor ceramic insulators.<\/p>\n

    The economics explain the growth. Millions of factory pre-coated cap and pin units now run on lines where frequent washing had become unaffordable. Coated ceramic has gained market ground where much lower inspection costs outweigh a higher acquisition price.<\/p>\n

    Peru shows all three options inside one grid. The country’s TSO installed polymeric insulators between 1996 and 2004 to cut washing on coastal lines. After 17 core-fracture failures within a few years, it specified RTV-coated glass from 2009 for the worst coastal sections. Washing burden, housing failure and coating adoption each had a role.<\/p>\n

    \"Cap-and-pin
    Cap-and-pin strings on a gantry, the classic coating candidates<\/figcaption><\/figure>\n

    The boundary for a buyer follows from that record. A silicone rubber housing already supplies the hydrophobic surface a coating would add, so coating a healthy composite string buys nothing. Coating belongs where a ceramic string carries a washing burden the budget can no longer carry. Choosing between a composite string and a coated ceramic one is a design decision made once, not a maintenance patch applied mid-life.<\/p>\n

    Washing Mistakes That Turn a Cleanup Into a Hazard<\/h2>\n

    Most washing harm traces to five habits, and all five are avoidable with discipline the crew already has.<\/p>\n